• 60 watts rated power
• Distortion less than 2% THD
• Transient protection diodes
• Frequency response -2dB from 20Hz to 20kHz
• Multiple output voltages/impedances available
• Resettable circuit breaker; thermally protected
• UL and CSA listed

• Power MOSFET circuitry
• Capable of continuous operation at rated output power
• Frequency response ±1dB, 20 - 20,000 Hz at full rated output
• Distortion less than 0.5% THD, 20 - 20,000 Hz
• Multiple output voltages/impedances available
• Automatic overload protection
• UL and C-UL listed

• Power MOSFET circuitry
• Capable of continuous operation at rated output power • Frequency response ±1dB, 20 - 20,000 Hz at full rated output
• Distortion less than 0.5% THD, 20 - 20,000 Hz
• Multiple output voltages/impedances available
• Automatic overload protection
• UL and C-UL listed

• 3 modes of operation to choose from - Stereo, Dual Mono, or 70V Mono
• Low noise, low distortion, and high slew rate
• Flexible modular input capability (2 module capacity)
• Professional, dual-channel (balanced or unbalanced), high-impedance input module with gain selection included
• 3 selectable low-frequency, roll-off choices
• 2x1 mixer function when in mono modes
• Insert connections for outboard equipment (in mono modes)
• Post- and Pre-EQ Output Feeds (summed mono out in stereo mode)
• DC, overload, short circuit, and thermal protection circuits
• Clip limiting circuits for speaker protection
• Power-saving Sleep Mode for intermittent use applications
• Status, Signal, and Clip/Limit indicators
• Back-Slope AC voltage stabilization for dependable performance over varying AC line voltages
• Heavy-gauge steel chassis with cast aluminum front panel
• Recessed volume control knobs with snap-on protective cover
• Mounts in 2 rack spaces (3-1/2") directly stackable without need for extra space above or below
• 2 independent, continuously variable, cooling fans for dependable and quiet operation
• Easily removable front fan grilles with filters
• Stable into 2-ohm loads

• 3 modes of operation to choose from - Stereo, Dual Mono, or 70V Mono
• Low noise, low distortion, and high slew rate
• Flexible modular input capability (2 module capacity)
• Professional, dual-channel (balanced or unbalanced), high-impedance input module with gain selection included
• 3 selectable low-frequency, roll-off choices
• 2x1 mixer function when in mono modes
• Insert connections for outboard equipment (in mono modes)
• Post- and Pre-EQ Output Feeds (summed mono out in stereo mode)
• DC, overload, short circuit, and thermal protection circuits
• Clip limiting circuits for speaker protection
• Power-saving Sleep Mode for intermittent use applications
• Status, Signal, and Clip/Limit indicators
• Back-Slope AC voltage stabilization for dependable performance over varying AC line voltages
• Heavy-gauge steel chassis with cast aluminum front panel
• Recessed volume control knobs with snap-on protective cover
• Mounts in 2 rack spaces (3-1/2") directly stackable without need for extra space above or below
• 2 independent, continuously variable, cooling fans for dependable and quiet operation
• Easily removable front fan grilles with filters
• Stable into 2-ohm loads 

• 3 modes of operation to choose from - Stereo, Dual Mono, or 70V Mono
• Low noise, low distortion, and high slew rate
• Flexible modular input capability (2 module capacity)
• Professional, dual-channel (balanced or unbalanced), high-impedance input module with gain selection included
• 3 selectable low-frequency, roll-off choices
• 2x1 mixer function when in mono modes
• Insert connections for outboard equipment (in mono modes)
• Post- and Pre-EQ Output Feeds (summed mono out in stereo mode)
• DC, overload, short circuit, and thermal protection circuits
• Clip limiting circuits for speaker protection
• Power-saving Sleep Mode for intermittent use applications
• Status, Signal, and Clip/Limit indicators
• Back-Slope AC voltage stabilization for dependable performance over varying AC line voltages
• Heavy-gauge steel chassis with cast aluminum front panel
• Recessed volume control knobs with snap-on protective cover
• Mounts in 2 rack spaces (3-1/2") directly stackable without need for extra space above or below
• 2 independent, continuously variable, cooling fans for dependable and quiet operation
• Easily removable front fan grilles with filters
• Stable into 2-ohm loads 

• Capable of handling 70V, 25V, 8-ohm, and 4-ohm speaker loads
• 8 module bays
• Wide selection of advanced plug-in modules (modules sold separately)
• 4 levels of priority between modules
• 2 module bays capable of handling plug-in signal processing output modules
• 11-segment LED output level meter monitors the output level of the power amplifier with Peak and Average meter switch
• Motorized master volume control can be remotely operated
• Lockable switch permits user to select either transformer-coupled outputs or a direct low impedance output
• 5-position barrier strip, with clamping washers, provides connections for speaker loads
• Bridging In/Out connector
• External access to priority mute buses
• Bridging jack and Mute terminals join multiple Power Vector amps and mixers together
• Independent volume control for each of the eight module bays
• Two-color LED for each channel indicates input signal or clipping
• Bass and treble control with bypass switch (located in module bay 6)
• 125 Hz Low Cut switch (located in module bay 6)
• Signal-processing insert jacks allow external equipment to be inserted between the pre-amp output and the power amp input
• Pre-EQ, unbalanced, buffered output signal (“post” all unit controls, but “pre” any external “Insert” equipment connected)
• Grounded, unswitched AC convenience receptacle with a 500W maximum capacity provided for external equipment
• 8 module security cover/filler plates included with amplifier (PVMC)
• Push-button remote volume control panel (Model RVCP, sold separately)
• Security cover to selectively protect volume, bass, and treble controls (Model PVSC, sold separately)
• Rack mountable (with rack mounting kit RPK87, sold separately)
• 2 rack spaces high (3-1/2")
• Listed to UL Standard 60065 for U.S. and Canada 

• Capable of handling 70V, 25V, 8-ohm, and 4-ohm speaker loads
• 8 module bays
• Wide selection of advanced plug-in modules (modules sold separately)
• 4 levels of priority between modules
• 2 module bays capable of handling plug-in signal processing output modules
• 11-segment LED output level meter monitors the output level of the power amplifier with Peak and Average meter switch
• Motorized master volume control can be remotely operated
• Lockable switch permits user to select either transformer-coupled outputs or a direct low impedance output
• 5-position barrier strip, with clamping washers, provides connections for speaker loads
• Bridging In/Out connector
• External access to priority mute buses
• Bridging jack and Mute terminals join multiple Power Vector amps and mixers together
• Independent volume control for each of the eight module bays
• Two-color LED for each channel indicates input signal or clipping
• Bass and treble control with bypass switch (located in module bay 6)
• 125 Hz Low Cut switch (located in module bay 6)
• Signal-processing insert jacks allow external equipment to be inserted between the pre-amp output and the power amp input
• Pre-EQ, unbalanced, buffered output signal (“post” all unit controls, but “pre” any external “Insert” equipment connected)
• Grounded, unswitched AC convenience receptacle with a 500W maximum capacity provided for external equipment
• 8 module security cover/filler plates included with amplifier (PVMC)
• Push-button remote volume control panel (Model RVCP, sold separately)
• Security cover to selectively protect volume, bass, and treble controls (Model PVSC, sold separately)
• Rack mountable (with rack mounting kit RPK87, sold separately)
• 2 rack spaces high (3-1/2")
• Listed to UL Standard 60065 for U.S. and Canada

• Capable of handling 70V, 25V, 8-ohm, and 4-ohm speaker loads
• 8 module bays
• Wide selection of advanced plug-in modules (modules sold separately)
• 4 levels of priority between modules
• 2 module bays capable of handling plug-in signal processing output modules
• 11-segment LED output level meter monitors the output level of the power amplifier with Peak and Average meter switch
• Motorized master volume control can be remotely operated
• Lockable switch permits user to select either transformer-coupled outputs or a direct low impedance output
• 5-position barrier strip, with clamping washers, provides connections for speaker loads
• Bridging In/Out connector
• External access to priority mute buses
• Bridging jack and Mute terminals join multiple Power Vector amps and mixers together
• Independent volume control for each of the eight module bays
• Two-color LED for each channel indicates input signal or clipping
• Bass and treble control with bypass switch (located in module bay 6)
• 125 Hz Low Cut switch (located in module bay 6)
• Signal-processing insert jacks allow external equipment to be inserted between the pre-amp output and the power amp input
• Pre-EQ, unbalanced, buffered output signal (“post” all unit controls, but “pre” any external “Insert” equipment connected)
• Grounded, unswitched AC convenience receptacle with a 500W maximum capacity provided for external equipment
• 8 module security cover/filler plates included with amplifier (PVMC)
• Push-button remote volume control panel (Model RVCP, sold separately)
• Security cover to selectively protect volume, bass, and treble controls (Model PVSC, sold separately)
• Rack mountable (with rack mounting kit RPK87, sold separately)
• 2 rack spaces high (3-1/2")
• Listed to UL Standard 60065 for U.S. and Canada

• Capable of handling 70V, 25V, 8-ohm, and 4-ohm speaker loads
• 8 module bays
• Wide selection of advanced plug-in modules (modules sold separately)
• 4 levels of priority between modules
• 2 module bays capable of handling plug-in signal processing output modules
• 11-segment LED output level meter monitors the output level of the power amplifier with Peak and Average meter switch
• Motorized master volume control can be remotely operated
• Lockable switch permits user to select either transformer-coupled outputs or a direct low impedance output
• 5-position barrier strip, with clamping washers, provides connections for speaker loads
• Bridging In/Out connector
• External access to priority mute buses
• Bridging jack and Mute terminals join multiple Power Vector amps and mixers together
• Independent volume control for each of the eight module bays
• Two-color LED for each channel indicates input signal or clipping
• Bass and treble control with bypass switch (located in module bay 6)
• 125 Hz Low Cut switch (located in module bay 6)
• Signal-processing insert jacks allow external equipment to be inserted between the pre-amp output and the power amp input
• Pre-EQ, unbalanced, buffered output signal (“post” all unit controls, but “pre” any external “Insert” equipment connected)
• Grounded, unswitched AC convenience receptacle with a 500W maximum capacity provided for external equipment
• 8 module security cover/filler plates included with amplifier (PVMC)
• Push-button remote volume control panel (Model RVCP, sold separately)
• Security cover to selectively protect volume, bass, and treble controls (Model PVSC, sold separately)
• Rack mountable (with rack mounting kit RPK87, sold separately)
• 2 rack spaces high (3-1/2")
• Listed to UL Standard 60065 for U.S. and Canada

• Capable of handling 70V, 25V, 8-ohm, and 4-ohm speaker loads
• 8 module bays
• Wide selection of advanced plug-in modules (modules sold separately)
• 4 levels of priority between modules
• 2 module bays capable of handling plug-in signal processing output modules
• 11-segment LED output level meter monitors the output level of the power amplifier with Peak and Average meter switch
• Motorized master volume control can be remotely operated
• Lockable switch permits user to select either transformer-coupled outputs or a direct low impedance output
• 5-position barrier strip, with clamping washers, provides connections for speaker loads
• Bridging In/Out connector
• External access to priority mute buses
• Bridging jack and Mute terminals join multiple Power Vector amps and mixers together
• Independent volume control for each of the eight module bays
• Two-color LED for each channel indicates input signal or clipping
• Bass and treble control with bypass switch (located in module bay 6)
• 125 Hz Low Cut switch (located in module bay 6)
• Signal-processing insert jacks allow external equipment to be inserted between the pre-amp output and the power amp input
• Pre-EQ, unbalanced, buffered output signal (“post” all unit controls, but “pre” any external “Insert” equipment connected)
• Grounded, unswitched AC convenience receptacle with a 500W maximum capacity provided for external equipment
• 8 module security cover/filler plates included with amplifier (PVMC)
• Push-button remote volume control panel (Model RVCP, sold separately)
• Security cover to selectively protect volume, bass, and treble controls (Model PVSC, sold separately)
• Rack mountable (with rack mounting kit RPK87, sold separately)
• 2 rack spaces high (3-1/2")
• Listed to UL Standard 60065 for U.S. and Canada

• Push-button operation of motorized master volume control (up to 2000 ft. away)
• Fits standard single gang electrical box
• Multiple RVCP's may be paralleled